Speed Controller Generator Accessories Control Engine Fast Precise Response To Transient Load Changes

1. SPECIFICAT-parts-partsIONS
1.1 Electronic SpecifiCAT-parts-partsions
Operating Voltage
12 or 24 VDC ±20%
Output Current
0.5 ~ 15 A
Run Speed Adjustment range
Speed adjustment Potentiometer (30 turn)
4 Segment Dip Switch Adjustable From 600 ~ 9500
Hz.
Idle Speed Adjustment Range
Run Speed 30 ~ 85%
Ramp Time
3 ~ 20 Sec
Remote Speed Pot
Ext. Remote speed pot terminal 6, 7, 8 (ILS) and 6,
7, 9 connect a 5K potentiometer ±5% adjustment
range.
Temp. Stability
<0.01%
Run Speed Stability
± 0.25 % at steady state
MPU input signal
1 ~ 120VAC RMS
Droop
4%
Adjustment
Run Speed, Idle Speed,
Ramp Time, Droop, Integration, Gain
Mechanical Vibration
1G @ 18 ~ 30 Hz, 2.5G @ 48 ~ 70 Hz
Relative Humidity < 95%
Operating Temperature -40 ~ 85℃
Storage Temperatur -40 ~ 85℃
Dimensions 147mm L * 114mm W * 50mm H
Weight 690g ± 2%

2 Function Descriptions
The EG2000 provides both an adjustable Idle
Speed and ramp, for controlling engine smoke,
vibration and warm-up.
2.1 Controller
Together, the EG2000 Controller, Actuator and
MPU (Magnetic Pickup) form the electronic engine
governor assembly.
The EG2000 receives the signal from the MPU and,
depending on the engine RPM, the actuator controls
the fuel intake on the engine.
The EG2000 receives its power from the engine
batteries or an AC to DC power supply rated from 12
or 24 VDC ±20% matching the Actuator voltage.
The average operating current is around 2.5 to 3.5
amps, but it may reach 15 Amps during engine start
or sudden load changes.
2.2 Installation Descriptions
1. Protect the EG2000 by installing it inside the
engine instrument control panel.
2. Mount the Actuator close to the engine fuel
system. See actuator manufacture instructions.
3. Always choose a point on the actuator control
arm in which it can rotate freely, providing
minimum and maximum fuel (But do not bottom
out the actuator; leave 2 to 3 degrees before the
off and on position).
4. Use a Non-Linear link on Gas engines to get low
Gain at light loads and high Gain at heavy loads
and a linear link on diesel ejection pumps.

DIMENSION AND TYPICAL WIRING DIAGRAM

Since establishment in 1985, Guangdong ALI Testing Equipment Co., Ltd, a wholly-owned subsidiary of GSKA Group has been providing a wide and complete range of products and services to the society. GSKA has now 16 offices, warehouses and service centres in China, with head office loCAT-partsed in Hong Kong. There are more than 100 employees in GSKA Group, and we are expanding into many industries with rapid expanding pace of China.

There are mainly 4 departments in GSKA Group, namely:

1) Construction and Mining equipment

GSKA has been cooperating with many international famous brands in China, such as Ingersoll-rand, Atlas Copco and Liebherr. Our products include concrete batching plants, concrete mixers, hydraulic crawler drills, pneumatic crawler drills, water well drills, air compressors, road compactors, breakers and various other equipment. We are major in several industries, such as hydro-electric power plants, cement quarries, coal mines and railway systems.

In order to provide a quick response to our customers, we have stocked over US$1.5 Million spare parts of Ingersoll-rand and Atlas Copco in our Chinese warehouse. Recently, we have exported small air compressors, pneumatic crawler drills, water well drills and drilling accessories and spare parts to overseas market.

2) Power Group

GSKA has been supplying CAT-parts and Broadcrown gensets for more than 15 years. Our major customers include Telecoms, Banks, Airports, Factories and many other sectors in the society. We are also doing assembly of gensets in China, under our brand name of "GSKA " with ratings from 1KVA to 2000KVA. The quality of "GSKA " genset has won a very good reputation from customers in China and overseas market.

We are also the specialists for genuine spare parts, such as CAT-parts, Perkins, FG Wilson, Cummins, , Volvo, etc.

Besides gensets, we also provide total solution on the power problems, such as Powerware - UPS, DC system and battery ,lightning equipment and many other electronic products.

3) Security and IT Group

GSKA acquired famous USA brand name Locktronix in 2004 and started manufacture electric locks in China. Since then, we have been exported products to the Middle East, South Asia and Africa. Our market is expanding each year and we are looking for more distributors in different countries to be our business partners. Besides electric locks and accessories, we have also developed our own access control system by our software team. The system includes smart card solution and also biometric access control, such as hand-key, fingerprint and facial recognition. Our EC-PAYROLL system has been widely used in many factories both in Hong Kong and mainland China.

After all, GSKA has an objective of "Always Provide the Best" and we shall consistently provide high quality products and reliable services to our worldwide customers. We are looking forward to making good business with our partners