1. Standby power:24 kw
2.Engine Make & Model:Perkins 404C-22G1 HS
3.Alternator Model:LL1012N
4.Fuel Tank Capacity: litres (US gal):45 (11.9)
5.Cooling Method: Water Governing
6.Compression Ratio: 23.3:1
7.Displacement: l (cu.in) 2.2 (135.2)
8.Bore/Stroke: mm (in) 84.0 (3.3)/100.0 (3.9)
9.Moment of Inertia: kg m² (lb. in²) 3.20 (10935)
10.Weights: kg (lb) :446 (983)
3 Pole MCB Perkins Engine Generator , 404C-22G1 HS
Output Ratings |
Generating Set Model | * JPPH30E2 Prime* Standby* |
380-415V, 50 Hz | * 30.0 kVA * 24.0 kW |
220/127V, 60 Hz | * * * * |
- Refer to ratings definitions on page 4.
Ratings at 0.8 power factor.
Technical Data |
Engine Make & Model: | Perkins 404C-22G1 HS |
Alternator Model: | LL1012N |
Base Frame Type: | Heavy Duty FabriCAT-parts-partsed Steel |
Circuit Breaker Type: | 3 Pole MCB |
Frequency: | 50 Hz 60 Hz |
Engine Speed: RPM | 3000 - |
Fuel Tank Capacity: litres (US gal) | 45 (11.9) |
Fuel Consumption: P16.5P2 l/hr (US gal/hr) | - - |
Fuel Consumption: P18E2 l/hr (US gal/hr) | 8.9 (2.4) - |
PH30E2
Engine Technical Data
Physical Data
Manufacturer: Perkins
Model: 404C-22G1 HS
No. of Cylinders/Alignment: 4 / In Line
Cycle: 4 Stroke
Induction: Naturally Aspirated
Cooling Method:Water Governing
Type: Mechanical Governing
Class:ISO 8528 G2
Compression Ratio: 23.3:1
Displacement: l (cu.in) 2.2 (135.2)
Bore/Stroke: mm (in) 84.0 (3.3)/100.0 (3.9)
Moment of Inertia: kg m² (lb. in²) 3.20 (10935)
Engine Electrical System:
-Voltage/Ground: 12/Negative
-Battery Charger Amps: 55
Weight: kg (lb)
- Dry: 218 (481)
- Wet: 234 (517)
Air System 50 Hz 60 Hz
Air Filter Type:Replaceable
Element Combustion Air Flow: m³/min (cfm)
-Standby: 2.4 (85)
-Prime:
- Max. Combustion Air Intake
Restriction: kPa (in H2O) 6.4 (25.7)
- Radiator Cooling Air Flow: m³/min (cfm) 71.0 (2507)
- External Restriction to
Cooling Air Flow: Pa (in H2O) 125 (0.5)
Cooling System 50 Hz 60 Hz
Cooling System Capacity:l (US gal) 6.8 (1.8)
- Water Pump Type: Centrifugal
Heat Rejected to Water & Lube Oil: kW (Btu/min)
-Standby: 29.3 (1666)
-Prime:
- Heat Radiation to Room:kW (Btu/min)
-Standby: 11.9 (677)
-Prime: -
- Radiator Fan Load: kW (hp) 1.2 (1.7)
Cooling system designed to operate in ambient conditions up to 50°C
(122°F).
Contact your local FG Wilson dealer for power ratings at specific
site conditions.
Performance 50 Hz 60 Hz
Engine Speed: RPM 3000
- Gross Engine Power: kW (hp)
-Standby: 31.9 (43.0)
-Prime: -
- BMEP: kPa (psi)
-Standby: 1151.0 (167.0) -
-Prime: -
- Regenerative Power: kW 19.0
LubriCAT-parts-partsion System
Oil Filter Type: Spin-On, Full Flow
Total Oil Capacity l (US gal): 10.6 (2.8)
Oil Pan l (US gal): 8.9 (2.4)
Oil Type: AP1CH4 15W-40
Cooling Method: Water
Fuel System
Fuel Filter Type: Replaceable
Element Recommended Fuel: Class A2 Diesel
Fuel Consumption: l/hr (US gal/hr)
110% 100% 75% 50%
Load Load Load Load
PH30E2
50 Hz 8.9 (2.4) 7.1 (1.9) 5.6 (1.5)
60 Hz - - -
(based on diesel fuel with a specific gravity of 0.85 and
conforming to BS2869, Class A2)
Exhaust System 50 Hz 60 Hz
Silencer Type: Level 1
Silencer Model & Qty: MXC0996 (1) Pressure Drop Across
Silencer System: kPa (in Hg) 5.03 (1.485)
- Silencer Noise Reduction
Level: dB -
- Max. Allowable Back
Pressure: kPa (in. Hg) 10.2 (3.0)
- Exhaust Gas Flow:
m³/min (cfm)
-Standby: 7.6 (268) -
-Prime: -
- Exhaust Gas Temperature: °C (°F)
m³/min (cfm)
-Standby: 475 (887) -
-Prime: - -
PH30E2
Alternator Performance Data
Data Item | 50 Hz |
415/240V | 400/230V | 380/220V |
Motor Starting Capability* kVA | 62 | 58 | 53 |
Short Circuit Capacity** % | 0 | 0 | 0 |
Reactances: Per Unit Xd X'd X''d | 3.480
0.090
0.044 | 3.750
0.100
0.047 | 4.160
0.110
0.052 |
Reactances shown are applicable to prime ratings
- Based on 30% voltage dip. Improved motor starting capability is
available with optional Permanent Magnet generator or AREP
excitation.
** With optional Permanent Magnet generator or AREP excitation.
Alternator Technical Data
Physical Data Operating Data |
Manufacturer: FG WILSON | Overspeed: RPM 4500 |
Model: LL1012N | Voltage Regulation (steady state) (%): + /- 0.5 |
No. of Bearings: 1 | Wave Form NEMA = TIF: 50 |
Insulation Class: H | Wave Form IEC = THF: 2.0% |
Winding Pitch Code: 2/3 - 6 | Total Harmonic Content LL/LN: 4.0% |
Wires: 12 | Supression is in line with European Standard Radio Interference: EN61000-6 |
Ingress Protection Rating: IP23 | Radiant Heat: kW (Btu/min) -50 Hz: 4.2 (239) -60 Hz: - |
Excitation System: SHUNT |
AVR Model: R230 |
Technical Data
3 Phase Ratings and Performance at 50 Hz, 3000 RPM
3 Phase Ratings and Performance at 60 Hz,
Voltage Prime Model Standby Model Voltage Prime Model Standby Model PH30E2 |
| kVA kW | kVA kW | kVA kW | kVA kW |
415/240V | - - | 30.0 24.0 |
|
|
400/230V | - - | 30.0 24.0 |
|
|
380/220V | - - | 30.0 24.0 |
|
|
Definitions
Standby Rating
These ratings are applicable for supplying continuous electrical
power (at variable load) in the event of a utility power failure.
No overload is permitted on these ratings. The alternator on this
model is peak continuous rated (as defined in ISO 8528-3).
Prime Rating
These ratings are applicable for supplying continuous electrical
power (at variable load) in lieu of commercially purchased power.
There is no limitation to the annual hours of operation and this
model can supply 10% overload power for 1 hour in 12 hours.
Standard Reference Conditions
Note: Standard reference conditions 27°C (80°F) Air Inlet Temp,
152.4m (500ft) A.S.L. 60% relative humidity. Fuel consumption data
at full load with diesel fuel with specific gravity of 0.85 and
conforming to BS2869: 1998, Class A2.
Weights and Dimensions
Weights: kg (lb) Dimensions: mm (in)
Net (+ lube oil) |
439 (968) |
Length |
1320 (52.0) |
Wet (+ lube oil & coolant) | 446 (983) | Width | 552 (21.7) |
Fuel, lube oil & coolant | 484 (1067) | Height | 1258 (49.5) |
General Data
Documents
A full set of operation and maintenance manuals, circuit wiring
diagrams, and commissioning/fault finding instruction leaflets.
Generating Set Standards
The equipment meets the following standards: BS5000, ISO 8528, ISO
3046, IEC 60034, VDE 0530, NEMA MG-1.22.
FG Wilson is a fully accredited ISO 9001 company.
Warranty
All equipment carries full manufacturer's warranty. Extended
warranty terms available.
